Control-X Chest X-Ray System

A dual column system with motorized tube stand in slave configuration to the wall stand. After adjusting the height of the digital detector to the patient size and pressing the „GO” button, the X-ray tube drives in position centered to the digital panel. Optional motorized movement on the wall stand is available.
Long vertical travel allows for the lowest and highest exposure positioning in unison with tube stand
Fully counter-balanced, double rope system for safety
Electrical lock for easy positioning and permanent placement, manual drive
Detector heights can be adjusted according to the patient height, and using the tracking push-button the TS 99 CHEST Stand moves the tube in the required height
Panel cover has permanent cross-lines and AEC field’s marks for easy patient positioning.
Wall box with terminal strips and cable covering hosing for professional look installation.
Special grid cabinet (for fixed grid, 215 LPI, 10:1) for full-size Flat Panel Detector.
AEC detector
0.6 / 1.2 mm focus, 18/50 kW, 300 kHU, 12° target angle
10 m standard (longer cable pairs available)
High/Standard Speed.
Fixed SID
X-ray tube follows receptor center
Full DX modality
50 kW – 80 kW, 100 kHz, 400 to 1000 max mA, 40 to 150 kV range (depending on X-ray tube selected - please inquire for X-ray tube upgrades
Power Requirements: 208- 400VAC three-phase (please specify input power when ordering)
Optional line matching transformers are available for an additional cost
Optional single-phase stored energy version up to 50 kW; 6.5 / 10 / 20 or 30 kWs stored energy (approx. 65/100/200/300 mAs exposures @ 100 kV)
Microprocessor control delivers reliable and accurate exposure parameter management
Can operate as a three-point (kV, mA and time), or a two-point (kV and mAs) or AEC technique selection generator
Optional interface for AEC, high speed starter, DAP
Rapid automatic calibration mode reduces installation time
Automatic tube protection and safety interlocks are standard features
Compact Size: 60 cm x 40 cm x 50 cm (L x W x D), SE version (20/30 kWs): 90 cm x 40 cm x 50 cm
Motorized vertical movement, tracking with the WS 99 CHEST stand
Electrical locks with clutches, manual movement allowed
Very quiet, “Easy-glide” effortless operation with quality bearing systems
Fully counter-balanced, spring-loaded system
Trunnion ring for the x-ray tube, plastic cover.
Floor-only mounting, fixed SID to the chest stand
43 cm x 43 cm image size - no rotation required
Pixel matrix 3008 (H) x 3072 (V)
Pixel pitch 143 µm
Long vertical travel allows for the lowest and highest exposure positioning in unison with tube stand
Fully counter-balanced, double rope system for safety
Electrical lock for easy positioning and permanent placement, manual drive
Detector heights can be adjusted according to the patient height, and using the tracking push-button the TS 99 CHEST Stand moves the tube in the required height
Panel cover has permanent cross-lines and AEC field’s marks for easy patient positioning.
Wall box with terminal strips and cable covering hosing for professional look installation.
Special grid cabinet (for fixed grid, 215 LPI, 10:1) for full-size Flat Panel Detector.
AEC detector
0.6 / 1.2 mm focus, 18/50 kW, 300 kHU, 12° target angle
10 m standard (longer cable pairs available)
High/Standard Speed.
Fixed SID
X-ray tube follows receptor center
Full DX modality
50 kW – 80 kW, 100 kHz, 400 to 1000 max mA, 40 to 150 kV range (depending on X-ray tube selected - please inquire for X-ray tube upgrades)
Power Requirements: 208- 400VAC three-phase (please specify input power when ordering)
Optional line matching transformers are available for an additional cost
Optional single-phase stored energy version up to 50 kW; 6.5 / 10 / 20 or 30 kWs stored energy (approx. 65/100/200/300 mAs exposures @ 100 kV)
Microprocessor control delivers reliable and accurate exposure parameter management
Can operate as a three-point (kV, mA and time), or a two-point (kV and mAs) or AEC technique selection generator
Optional interface for AEC, high speed starter, DAP
Rapid automatic calibration mode reduces installation time
Automatic tube protection and safety interlocks are standard features
Compact Size: 60 cm x 40 cm x 50 cm (L x W x D), SE version (20/30 kWs): 90 cm x 40 cm x 50 cm
Motorized vertical movement, tracking with the WS 99 CHEST stand
Electrical locks with clutches, manual movement allowed
Very quiet, “Easy-glide” effortless operation with quality bearing systems
Fully counter-balanced, spring-loaded system
Trunnion ring for the x-ray tube, plastic cover.
Floor-only mounting, fixed SID to the chest stand
43 cm x 43 cm image size - no rotation required
Pixel matrix 3008 (H) x 3072 (V)
Pixel pitch 143 µm